Usually the belt
Snapped or jumped drive belt. $20 part. One of the cheapest dryer repairs. GE belts in the van.
GE dryer humming but drum won't turn?
Most often a snapped drive belt ($20 part). On GE, also check the front bearing glide — when it seizes, the drum locks. Visual check in 5 minutes tells us exactly what failed. If we don't fix it, you don't pay.
30 minutes
Open the top panel, swap the belt, reassemble. Rollers and front bearing glide checked at the same time.
GE parts in the van
GE drive belts, drum support rollers, and front bearing glide kits — stocked for same-day repair.
If we don't fix it, you don't pay
Licensed & Insured
California state appliance repair license
Free Vent Inspection
Clogged vent is a fire hazard. We check and clean it with every repair
90-Day Warranty
On parts and labor
9 of 10 Fixed Same Day
Belts, rollers, heating elements — all in the van
Dmitry
GE Dryer Tech · Orange
1,500+ dryers repaired. GE's drum design has one quirk the other brands don't: a front bearing glide — a nylon insert that supports the front of the drum. When it wears out completely, the drum can seize rather than just squeak.
Key signal: motor humming but drum completely still = belt or bearing glide seized. No sound at all = thermal fuse or door switch (see "won't start").
My GE recommendation: if the belt snapped on a dryer 8+ years old, I check and replace the front bearing glide and rear rollers at the same time. Same disassembly, all three done together — saves a second service call.
How the repair works
From your call to a working dryer — here's exactly what happens
1. Call Us
Describe what's happening. Dmitry asks 2–3 questions and gives you a ballpark price on the spot.
2. Diagnostics + Vent Check
Dmitry tests the element, belt, rollers, motor — and always checks the exhaust duct. A clogged vent is a fire hazard.
3. Approve the Quote
Happy with the price — we fix it. Not happy — you only pay $89 for the diagnostic.
4. Repair + Free Vent Clean
We replace the part, clean the vent at no charge, run a full heat cycle, and show you how to prevent the issue from coming back.
5 reasons a GE drum stops spinning
One look — 5 minutes — and we know what to fix
1. Broken belt (75%)
Most common GE call. Motor hums, drum frozen. Fixed in 30 minutes. Labor: $80. Part: $20.
2. Worn drum support rollers (10%)
Rollers seize — drum sags and can't rotate. Grinding before it stops. Always replaced in pairs. Labor: $80. Part: $40.
3. Seized front bearing glide (10%)
GE-specific: the nylon glide that supports the drum front wears or melts — drum locks. Labor: $80. Part: $25–$45.
4. Failed idler pulley (3%)
Belt tensioner seizes — often alongside the belt on older GE models. Labor: $80. Part: $25.
5. Door switch (2%)
Complete silence at startup = switch not signaling 'door closed.' Labor: $80. Part: $15–$40.
Why we fix your dryer right the first time
The average tech: "not heating — swap the element" ($150). Didn't help. "Then the thermal fuse" ($80). Still nothing. You pay three times. Our analyzer reads amperage on the element, air temp, and vent airflow in 5 minutes. One part, one visit — no guessing.
1500
+
dryers repaired
5
min
diagnostics
95
%
fixed first visit
Check this yourself in 2 minutes
Sometimes you don't need a tech
Spin the drum by hand
Open the door — spins completely freely? Belt is broken. Grinds or won't budge? Bearing glide or rollers.
Do you hear it hum?
Humming = motor is working, problem is mechanical. Total silence = switch, fuse, or motor.
Door fully latched?
GE has a door switch — if the door doesn't click fully closed, the dryer won't start.
Overloaded?
A very heavy wet load can stall the drum and snap the belt. Don't dry heavy single items alone.
Quick Diagnosis: What's happening?
Check the symptoms you're seeing to find the likely cause and repair cost
Likely a simple fix
Probable cause: belt, rollers, or thermal fuse. Repair: $100–$180, 30–45 minutes.
Professional diagnostics needed
Probable cause: heating element + clogged vent, or moisture sensor. Repair: $120–$220, 30–60 minutes.
Serious issue — call now
Multiple symptoms + burning smell — possible clogged vent (fire risk) or control board failure. Call immediately.
What does GE drum repair cost?
Labor rate is flat. Parts are at cost plus markup. We quote everything BEFORE we start.
| Issue | Labor (flat) | Part | Total |
|---|---|---|---|
| Not heating (element / gas igniter) | $80 | $40–$140 | $120–$220 |
| Drum won't spin (belt) | $80 | $20–$100 | $100–$180 |
| Won't start (thermal fuse) | $80 | $15–$70 | $80–$150 |
| Noisy / squeaking (drum rollers) | $80 | $40–$120 | $120–$200 |
| Takes too long (clogged vent / sensor) | $80 | $0–$60 | $80–$200 |
| Error code (control board) | $120–$180 | $60–$200 | $180–$350 |
Diagnostic fee: $89 — waived when you book the repair.
If we don't fix it, you don't pay. Vent inspection included free with every repair.
GE drum repair: $100–$180 (labor + part). 75% of cases — belt for $20.
One of the least expensive dryer repairs. No reason to replace the machine.
Recent GE drum repairs in Orange
Samsung DVE45, Orange — "Clothes wet after full cycle"
Lisa ran 3 cycles — clothes still damp. Ready to buy a new dryer.
Heating element burned out. Thermal fuse intact.
40 min, $200 (labor $80 + part $120)
Savings vs new: $900
Lisa ran 3 cycles — clothes still damp. Ready to buy a new dryer.
Heating element burned out. Thermal fuse intact.
40 min, $200 (labor $80 + part $120)
Savings vs new: $900
LG DLG, Anaheim — "Gas dryer, worried about safety"
Gas dryer running cold. Owner concerned about gas leak.
Cracked igniter — no spark. Gas supply and connections safe.
35 min, $170 (labor $80 + part $90)
Gas dryer running cold. Owner concerned about gas leak.
Cracked igniter — no spark. Gas supply and connections safe.
35 min, $170 (labor $80 + part $90)
Whirlpool Cabrio, Tustin — "Stopped spinning mid-cycle"
Dryer stopped spinning with wet clothes inside.
Drive belt snapped. Drum rollers partially worn.
35 min, $140 (labor $80 + part $60)
Dryer stopped spinning with wet clothes inside.
Drive belt snapped. Drum rollers partially worn.
35 min, $140 (labor $80 + part $60)
Questions before you call
On GE dryers 8+ years old — yes. The front bearing glide and belt are accessed in the same disassembly. If the glide is worn (you'll see a groove worn into the nylon), doing it now avoids a second $80 labor charge later. I'll check it while I'm inside and tell you honestly if it needs to come out.
Usually one rear roller worse than the other — drum rocks and lurches. Keep running it and it will snap the belt and score the drum shaft. Roller pair: $80 + $40. Fix it early.
Relay fires, motor isn't starting. Could be the motor start winding, door switch, or a capacitor. Analyzer isolates the failing component in 5 minutes.
Most dryer repairs run $120–$220 total (labor + part). The most common issues — belt, rollers, heating element — are $20–$140 for the part and $80 for labor. We quote the exact price before we start, after diagnostics.
Depends on the machine. Here's how Dmitry looks at it:
Dryers are the most repair-friendly appliance out there. Parts are simple and cheap: belt $20, rollers $40, element $80, thermal fuse $15. They last for years — no sensitive electronics dying after three.
Real example: A Whirlpool 22 years old — replaced rollers twice at $40 each. Still runs. A Samsung 5 years old — control board failed, $400 repair. The old one was more reliable.
Exception: motor + board + element all at once on a 15+ year-old machine — we'll do the math together. If the repair exceeds $400 and the dryer is over 12 years old, sometimes a new one makes more sense.
Average repair: $150. New dryer: $700–$1,500 plus wait time. Full breakdown: repair vs. replace →
If we don't fix it, you don't pay. You only pay $89 for the diagnostic (service call + analyzer). More about our guarantee →
We're based in Orange. Usually 2–3 hours from your call. 9 out of 10 dryer repairs are done same-day: belts, rollers, heating elements — we carry them in the van.
Yes, if the vent is clogged. Wet lint builds up → overheating → ignition. According to NFPA, roughly 2,900 dryer fires happen in the US every year.
We clean the vent duct free with every repair. If it's been a while — call us, we'll check it. Usually $80–$150 if it's just a cleaning with no repair.
70% of the time — yes, it's a clogged vent or flex hose. The element heats, but humid air can't escape. We check airflow with the analyzer.
The other 30%: moisture sensor or heating element running below capacity. The analyzer shows which one in under 5 minutes.
A handyman does a bit of everything. Appliance repair is its own licensed specialty in California.
We have a diagnostic analyzer for pinpoint accuracy, a van stocked with parts, and direct supplier relationships with Samsung, LG, Whirlpool, and Maytag. A handyman will Google it — we see these failures every day.
$89 — waived when you go ahead with the repair. If we don't fix it, you don't pay. You only pay the diagnostic fee if you decide not to proceed.
What customers say
★ ★ ★ ★ ★
Loud squeaking every rotation on our Samsung DV. Tech said Samsung drum rollers wear unevenly and you have to replace all four at once or the noise comes back in 6 months — replaced all of them. Silent now.
★ ★ ★ ★ ★
LG gas dryer not heating. Worried about safety. Tech found a cracked igniter, replaced it, and did a full gas leak check — all included. Fast and thorough.
★ ★ ★ ★ ★
Samsung dryer ran full cycles but clothes stayed damp. Heating element burned out. Fixed in 40 min for $200. New dryer would have been $1,100.
Useful pages
When fixing your dryer makes sense — and when it doesn't
tS, hE, dE — what they mean and what the repair costs
If we don't fix it, you don't pay. 90 days on parts and labor
Recent repairs nearby
35 min $170Gas dryer running cold. Owner concerned about gas leak.
35 min $140Dryer stopped spinning with wet clothes inside.
40 min $200Lisa ran 3 cycles — clothes still damp. Ready to buy a new dryer.
30 min $80Amy's dryer taking 3 hours per load. Electric bill doubled.
We repair all major dryer brands
Other dryer problems
Similar symptoms? Check if there's more than one thing going on.
GE drum sitting still while laundry piles up?
One call — GE spinning again
✓ GE belts, roller kits, and front bearing glides in the van
✓ Belt replacement — 30 minutes
✓ $80 flat-rate labor
✓ If we don't fix it, you don't pay
7725 Gateway, Irvine, CA 92618
Пн-Пт 8:00-19:00
Ph: (949) 739-8878